Distribution #box with #M12 sockets and built-in male 7/8″ (or M23) control connector

Classic distribution box family with 4, 6, 8 or 10 #socket #connectors. Sockets can be M12 or M8 (IEC 61076-2-101 , IEC 61076-2-104) .
Caps for unused sockets are available.
Control male connector is 7/8″ of 14 or 19 or 25 poles (M23 of 12 or 19 poles).
This solution allows to easily change the box without unwiring the system.
The picture shows type SK205PD.

Internal circuit can be customized according to customer’s request, for instance:

• independent and separated outputs
• series outputs
• parallel outputs
• AND/OR logic wiring
• electronic logic upon request

Distribution box with M8, M12 sockets and 7/8″ (M23) main plug

 

 

Read Full Post »

#Timers for #condensate drain electrovalves

For #electrovalves with square #connector
EN 175301-803 style A (former DIN 43650-A), ISO 4400;
long life, easy installation and programming;
SMD technology, small dimensions, no maintenance;
adjustable timer setting; multi-voltage;
installation in any position.
Analogue type:
interval time = from 0.5 to 45 minutes, adjustable
discharge time = from 0.5 to 10 seconds, adjustable
Digital type:
interval time = from 0.1 sec to 99 hours, adjustable
discharge time = from 0.1 sec to 99 hours, adjustable

DIN 43650 connector with timer for condensate drain electrovalve

Read Full Post »

Current-carrying Capacity. Cable Voltage Drop

Cable choice.
An important element of assessment is the length of the cable. Each meter of the cable causes a voltage drop proportional to the value of the current that runs through it, if cosf = 1 we have: V = IxR.
V = voltage drop, I = current, R = resistance of the cable. In the case of inductive loads (solenoid valves, motors, etc.) or with variable currents, the higher current peak must be considered to avoid even temporary loss of power, which could hinder the proper functioning of the equipment. The longer is the cable, the greater the voltage drop, the IEC allows maximum values drop from 3% to 5% of rated voltage. Greater values are admitted only for the current peaks (e.g.: engines starting), if they do not create functioning problems. To minimize the voltage drop the cable section should be increased. Here are some tables that can help to easily calculate the minimum theoretical cable section. See tables 3 and 4 on the page http://www.shield.net/files/catalogue/support/2.2.pdf
For example, an average continuous current 1 A with section 0,34 mm² and cable length 10 m generates a voltage drop of 1,3 V, which is approximately 5% of 24 V.

Read Full Post »

Electronic and reed proximity #sensors.

Shield switches for hydraulic, pneumatic or electric #cylinders with #magnetic piston. High switching power and sensitivity. Customized circuits available. Shielded or unshielded cables, pvc or halogenfree polyurethane cables. Complete range of mounting accessories.

Read Full Post »

Manufacturer of #M12 and M8 connectors

Shield manufacturs #IEC 61076, IEC 60947-5-2 #M8 and M12 circular #connectors, angled or straight, with shielded or unshielded cables, halogen free polyurethane cables, PVC or silicone cables, dynamic or static application; circuits: Led or special circuit available. Ratings up to 4A, 250V. Clean design.

Read Full Post »

DIN 43650 connectors

These connectors are also called as EN 175301-803, ISO 4400, ISO 6952, ISO 15217 #electrovalve #connectors. They can be made with shielded or unshielded #cables, halogen free polyurethane cables, PVC or silicone cables with dynamic or static application. Ratings up to 10A, 250V. Electronics: custom electronic circuit design available. This connector style is also available as field attachable version, with screw terminals or crimp contacts.
Link to www.shield.net .

DIN 43650 electrovalve connector

Read Full Post »

Connectors with 7/8″ thread metal nut

Shield manufactures #connectors for industrial #hydraulic, #pneumatic, electrical automation, illumination, trucks and various construction equipments. These photos show 7/8″ circular angled and straight connector series with shielded or unshielded cable. The cable materials can be chosen among a wide choice: halogen free, polyurethane, PVC, silicone, etc. Dynamic or static application. 2, 3, 4, 5, 6, 14 poles.

Gender configurations can be: standard male, female and hybrid male-contacts / female-thread, female-contacts / male-thread. Ratings up to 13A, 600V. IP68 over-molded cables. Clean design.
Receptacle can be supplied with frontal or rear assembly method.

 

Read Full Post »

Distribox: distribution box series with M8 and M12 connectors

#Distribution #Boxes with IEC 61076-2 standard #M8 and/or #M12 sockets are used more and more often in the connectivity industry. They can be applied in many fields such as industrial hydraulic, pneumatic and electrical automation, robot, illumination systems, textile machines, paper machines, trucks, construction equipment, laboratory instruments.

Standard and custom built-in circuits are available to meet the clients needs. Electronics: special electronic circuit can be included as well. Customized design. IEC, EN. Control devices can be cables, sockets or plugs.

Read Full Post »

#Spider #Box

The Spider Box is a modular solution: simple connections or complex bonded junctions according to client’s design can be wired and over-moulded with an efficient cost/quality rate. #Assembly with shielded or unshielded #cables. Up to 20 cables connections with multiple wires can be linked together. Electronics: standard circuit or built-in custom electronic circuits design are available. Hybrid versions with M8 and M12 connectors + direct cable junctions are also available. It’s the solution to reduce the design and cables assembling time in your project.
Some of the main advantages:
– Even a not skilled worker can assemble the machinery electrical parts.
– Easy maintenance for the machinery electrical parts.
– It reduces the stock part numbers.
– Possibility to built-in sophisticated electronic components as well.

 

   

Read Full Post »